Under the Microscope: $1,000 MAC 9 vs. $6,000 Atlas
Welcome back to Jim’s Armory. This is Season 1, Episode 5 of Jim’s Gun Garage. While Jim waits on parts for the MAC 9 DS build, he takes apart a really great 2011 – the Atlas Apollo – to see what makes it great. With the MAC already apart, he puts both guns’ parts side by side under a digital microscope. As the description puts it, the surprise isn’t how much quality $6,000 buys. It’s how little $1,000 does.
Safety First The Atlas is unloaded, with no magazine present and a chamber flag occupying the chamber, so it can’t be loaded.
Guide Rod Types Jim compares three guide rods:
- MAC: the factory rod needs a paper clip or small piece of wire in a hole to hold the spring compressed against the reverse plug. Be careful; it’s under a lot of pressure.
- Atlas: a tool-less guide rod. Push it forward, press a small button to deploy a catch, and the whole assembly comes out.
- Staccato XC: a Dawson tool-less rod, which works on the same idea but is open on the front.
The difference matters. If the retaining pin on an open design ever broke, a piece could come loose inside the gun. Jim hasn’t seen it happen, but he’s heard stories. The Atlas design wraps that piece fully inside, so even with a broken pin, it should stay put. That’s also why the Masterpiece Arms deliberately skips a tool-less rod: it’s meant for competition, where a surprise failure is the last thing you need. If Jim had to choose, he’d pick the Atlas style, though he notes Dawson makes good products too.
Shock Buffs The Atlas comes with a shock buff, which cushions the slide against the guide rod and can save you if you accidentally run a hot load. Jim warns against putting them in every gun you own. They can make a gun cycle unreliably unless it’s designed for them, and Atlas has worked out its spring weights, slide weight, and ammo with the buff in mind.
Slide Disassembly Jim removes the firing pin stop by pushing the firing pin in and sliding the stop down.
Pro-Tip: Never pull the spring off the firing pin. You’ll stretch it and risk light strikes. Instead, twist it into the coil – clockwise on this one – and it comes right off. Do the same to put it back on.
To remove the extractor, he pushes its hook off the breech face, using a cheaper sacrificial tool in place of his 10-8 Performance tools, and slides it out. He also points out a small relief Atlas cut where the slide meets the disconnector. It’s different from the narrow groove of a Marvel cut, like the one on the Kimber 2K11. Atlas keeps it very slight so it doesn’t weaken the two legs that strip the next round from the magazine, while still easing the slide’s path over the disconnector.
Frame Disassembly The thumb safety comes off with the hammer back and the safety halfway between on and off. Then the hammer goes forward before Jim removes the magwell with a 5/32 punch. He uses a roll pin punch because its domed tip sits in the pin’s divot without slipping.
Pro-Tip: Always drop the hammer before removing the magwell or mainspring housing. If the hammer is back, the mainspring pushes the housing down and parts fall out. Jim says that leads to a lot of desperate emails. If you run into trouble, post it in the comments, whoever’s video you were following, so everyone can benefit.
The hammer, sear, and disconnector pins come out easily, each going only one direction. Jim notes that the small pin on the hammer strut should never be tight on the strut; the strut needs to move freely. Watch that pin so you don’t lose it. He says you really only need a 5/32 punch, a 5/32 roll pin punch, and a 3/32 punch to work on 2011s, unless you’re modifying them.
The Grip Module The Alpha grip module comes off after removing the 1/16 and 3 mm screws and popping out the bushings. Jim likes this grip a lot – maybe more than the Chile grip on his XC. He notes the Alpha version is close to $900-1,000, while the regular grip is around $600.
Pro-Tip: Jim uses Loctite on one side of the grip screws and Vibra-TITE VC-3 on the other. Vibra-TITE coats the threads in rubber, resisting vibration while still coming out easily with a tool, and it can be reused.
The mag catch releases by pressing it while turning the lock left. Then the trigger – Atlas’s threaded trigger bow – slides out the back.
Internals Under Magnification This is where things get ugly.
- Hammer hooks: Per Ordnance spec, they should be 90°. The Tisas hooks have a strange notch and a curve. Jim is throwing it away.
- Sear: The Atlas sear has crisp, flat sides: roughly a .020 engagement face plus a 45° relief cut that kicks the sear out of the way. The Tisas sear is rounded over. Jim is appalled. He believes this is why the gun needs such heavy springs; with lighter springs, he expects hammer follow.
- Extractor: The Tisas extractor is terrible. In Jim’s experience, the extractor is one of the top places budget guns cut corners, with no hand fitting, no tuning, and no test firing.
- Disconnector: Not terrible, but noticeably different.
- Feed ramp: On the Tisas, the feed ramp bevel extends into the chamber. On the Atlas, it doesn’t, and it’s far more highly polished.
Slide Fit and Barrel Lockup The Atlas slide is smooth as glass, with barely any movement. The MAC is grittier and looser – not terrible, just not perfect. Barrel lockup tells the bigger story. With no recoil spring, the Atlas barrel hood doesn’t move at all. Jim explains that the link cams the barrel down so it stays locked briefly after firing; without that lock time, ports and comps wouldn’t work. On the MAC, there’s slight movement even with the slide held forward, and that affects accuracy more than slide fit. The Atlas barrel also shows signs of hand fitting on the lugs.
Frame Weight Comparison The MAC frame is visibly larger but weighs 257.5 g against the Atlas’s 249 g – lighter than Jim expected given its size.
Final Thoughts Jim points out that the other guns on his bench, including the Prodigy, Warrior, and Romulus, all follow Ordnance spec on the sear and hammer hooks. What he found in the Tisas parts is unlike anything he’s seen. Still, the frame is close enough to spec, the slide fit is good enough, and the barrel is okay. The bones are good, and every internal can be replaced. The MAC will never be an Atlas, but Jim believes it can still be a really good gun. Grip modules and non-functional beavertails are on order, and he’s still leaning toward the America Grip from Proxy. Subscribe and stay tuned for the next episode.
