Repairing the Hidden Flaws in the MAC 9 DS
Welcome back to Jim’s Armory. This is Season 1, Episode 4 of Jim’s Gun Garage, and the MAC 9 DS is back on the bench. Last episode, Jim confirmed the sear and hammer pin holes are in spec, but he found an obstruction in the sear pin hole and another in the slide’s extractor channel. This episode wasn’t supposed to happen – it should have been a straight part swap – but the factory defects have to be fixed before the build can move forward.
Clearing the Sear Pin Hole Jim doesn’t want to wrap sandpaper around a rod and open up the whole hole. He only wants to remove whatever is catching on the inside edge. So he uses a very fine #4 round needle file and works by feel, since he can’t actually see the problem.
Pro-Tip: Put some blue Sharpie on the pin to see where it’s rubbing. That’s how Jim figures out the high spot is on the back side of the hole.
After a little more filing on the back of the hole, a .110 gauge goes through. The sear pin itself should measure .110 plus zero, minus .002 – anywhere from .108 to .110. The pin Jim plans to use measures .1085, and it fits perfectly.
Grip Bushing Holes Are Too Small Jim still hasn’t picked a grip, but he has picked a new product from Atlas: tapered grip bushings. The thicker end goes toward the top, making the magwell slightly narrower inside so the magazine stops before it’s over-inserted. That matters because over-insertion can bend the ejector, and cheaper guns often have weak ejectors.
The bushings don’t go in. The grip bushing holes in the frame measure 7.8 mm – about .308 – while the bushings are .310. The factory bushings slide right in, but they use metric screws, and Jim is set on making this gun as American as possible. He doesn’t want to enlarge holes in hard steel, so he does what he calls something crazy: he files the bushings down from .310 to .308, checking as he goes, until they fit. The screws are Torx – not exactly American, but not metric either.
The front bushing has a different problem: the hole sits slightly ahead of the grip module. A little careful filing on the back side fixes the alignment. Jim skips the Loctite for now because he expects to take the gun apart a few more times.
Extractor Channel Obstructions Under magnification, the problem in the slide is obvious: a screw is sticking into the extractor channel. It’s not the optic screw. It’s the factory screw that mounts the AOS (Agency Optic System) plate. Jim has no issue with the plates themselves – he runs one on another gun with no trouble – but having a factory screw intrude into the extractor channel is, in his words, beyond stupid. The plate’s screws are very thin, because the plate uses a raised shoulder to get more thread engagement. That means you have to use their screws. These are 2 mm metric.
Pro-Tip: For tiny screw heads like these, use a hardened driver bit. Jim doesn’t know whether there’s Loctite in there, and he doesn’t want to risk breaking a tool.
Clearing the Extractor Channel With the screw out, the .209 gauge still stops partway. Under magnification, the rest of the tunnel looks rough. Jim’s fix: 600-grit wet/dry sandpaper attached to a rod with spray adhesive, used with oil. After working it, the gauge gets past the trouble spot. He’ll clean it and check it under magnification again, because he wants it as smooth as possible with no burrs.
What he sees looks like reamer ring formation. That can have several causes, but Jim thinks the most likely one is taking too much stock or going too fast. That forces the reamer to act like a drill bit, traps chips, and causes them to fuse to the inside of the hole.
“I Didn’t Know What I Was Getting Into” Jim admits the project has blown the budget and fought him every step of the way. He could have jammed the extractor back in or reused the factory bushings, but he’s a perfectionist, and that’s how he works safely.
There’s a twist: the MAC is no longer made, and the current version is the Tisas DS9. Jim bought one – actually ten – planning to upgrade them. The DS9 doesn’t have the MAC’s aggressive lightning cuts and has some texturing on top, and in his words, it isn’t any easier to rack. He hopes to hit his stride as he works through them.
Final Thoughts This was an unplanned episode, but it fixed real factory defects: a burr in the sear pin hole, undersized metric bushing holes, a factory plate screw protruding into the extractor channel, and a rough extractor tunnel. With those out of the way, the build can move forward. Subscribe and stay tuned for the next episode of Jim’s Gun Garage.
