Sig P211: Fake 2011 Outside. Real 2011 Inside?
Welcome back to Jim’s Armory. In this one, Jim takes on the debate surrounding the Sig P211 head-on: is it really a 2011, or just a 2011-shaped gun with proprietary parts stuffed inside? He’s already covered the P211 in a full teardown video (linked in the description), so this time he’s skipping the play-by-play of disassembly to focus on one question – which parts are proprietary Sig-only pieces, and which parts can be swapped for standard 2011 aftermarket components. To answer it, he installs a complete EGW ignition kit and puts it through function checks.
Safety First Jim starts, as always, by confirming the gun is unloaded with a chamber flag physically occupying the chamber, so there’s no way a round could be present.
Comparing Recoil Springs the Easy Way Before getting into the internals, Jim shows a trick for identifying recoil springs once the paint wears off from use. Pro-Tip: put both springs on a cleaning rod (with a washer if needed to fit a smaller rod) and push down on both at once – whichever one compresses first is the lighter spring. In this case, the two are an 8 lb and a 10 lb spring.
The Upper: Fully Proprietary Jim doesn’t spend much time on the slide, since he considers everything up top proprietary – the firing pin is retained with roll pins, and the spring is a different diameter than standard 2011 components. He moves on to the frame internals, which is where the real question lives.
MIM Parts and a Series 70 Conversion Pulling the hammer, sear, and disconnector, Jim points out the telltale signs of Metal Injection Molding (MIM) – ejector pin marks and a visible seam on the back of the disconnector. He walks through how MIM parts are made: oversized plastic-and-metal-dust moldings ejected with pins, then sintered at high temperature to burn away the filler and leave only metal. Not the same as billet, in his view, though he notes MIM has become common and well-refined. This particular gun also has a Series 70 conversion installed, adding a spacer plate into the mix.
The Trigger and Grip Module The trigger lifts out of the top rather than sliding out the back like a typical 2011. Jim tries fitting two Red Dirt triggers built for a Chile-style grip module, but neither clears – a standard 2011 magazine doesn’t even fit all the way through the P211’s grip module, since it only needs to clear P320 mags. His conclusion: you’re not swapping in a standard 2011 trigger without modifying the trigger bow, and even then it’d be purely cosmetic. The ejector, however, looks to be standard issue, and Jim suspects a standard part could be fitted here.
Testing the EGW Ignition Kit This is the heart of the video: Jim compares an EGW ignition kit, piece by piece, against the Sig factory parts.
- Plunger tube assembly: The front and rear plungers look identical to the factory parts. Jim believes this will work.
- Sear spring: A Wilson spring looks essentially the same shape as factory, just bent and tuned for the gun. He expects it to work, though the factory spring feels tighter by comparison.
- Disconnector: The EGW piece looks identical to the factory disconnector.
- Main spring: The main spring housing itself is proprietary – a staccato housing doesn’t fit the P211 grip, and the raised guide portions are shaped differently (straight vs. angled). But the cap and spring inside look like they could be standard parts. Comparing an ISMI 19 lb spring and an EGW 17 lb spring, the factory spring is shorter than both, so Jim suggests you could cut down a lighter spring to fit if you wanted to reduce spring weight. He test-fits the EGW spring directly and it works without feeling excessively tight.
- Sear: Looks a little different from the factory part, but once pinned in, the geometry and angle appear to match. Jim expects it to work.
- Hammer: The EGW skeletonized, lightened hammer fits over the pin, but the secondary safety hook location and hammer face angle differ slightly from factory. Jim isn’t sure how much this will matter functionally but proceeds anyway, adding a stainless hammer strut and strut pin from EGW.
Reassembly and Function Check Jim reassembles loosely – no full Loctite or final fitting – just to prove out function. Working around the existing Series 70 conversion, he gets the EGW disconnector, sear, and hammer in along with a Colt sear spring, adjusting it just enough to get things running rather than performing a full trigger job. The grip safety checks out, and a firing pin test against a block of wood confirms positive firing pin engagement.
Crucial Safety Checks With the swapped internals in place, Jim runs through his standard safety checks. For the grip safety, he confirms it stops the trigger bow from moving rearward, watching and listening for any sear movement even though the trigger shows a little takeup. For the thumb safety, he depresses the grip safety and pulls hard on the trigger, listening for any click that would indicate the sear shifting off the hammer hooks – none found, even with the different aftermarket sear installed. Finally, he checks the hammer’s secondary safety hooks, noting they now catch the hammer slightly further forward than with the factory hammer, but they still prevent the firing pin from being struck.
Final Thoughts So, how proprietary is the Sig P211? The grip module, main spring housing, and everything in the slide – firing pin, guide rod, recoil spring – are all proprietary to Sig. But the ignition components tell a different story: the plunger tube parts, sear spring, disconnector, sear, main spring, and even the skeletonized hammer from EGW all fit and functioned in Jim’s test, though he notes these kits aren’t turnkey and typically need some fitting and polishing. For Jim, the verdict is clear – underneath its P320-compatible, proprietary shell, the P211 really does run on 2011 internals.
That’s the teardown for this one. If you want the full disassembly of the P211, check the link in the description – and subscribe so you don’t miss the next deep dive.
